Official too lazy to search, noob friendly thread.

Is the cc and the ce boot of the same width? say i want to install a bootlip spoiler that was build for the ce, will it fit?
 
Rodger said:
Is the cc and the ce boot of the same width? say i want to install a bootlip spoiler that was build for the ce, will it fit?
Click to expand...
Yea
 
MOR31 said:
Rodger said:
Is the cc and the ce boot of the same width? say i want to install a bootlip spoiler that was build for the ce, will it fit?
Click to expand...
Yea
Click to expand...
Sure? I bought this one, and it was the wrong length for me CE, 85mm too long. Didn't read the year -.-
Measure the curved length of your boot edge and I'll measure mine. If it's about 85mm longer then get this one.
http://www.ebay.co.uk/itm/Painted-Mitsu ... AQ:GB:1123
 
Jazza said:
MOR31 said:
Rodger said:
Is the cc and the ce boot of the same width? say i want to install a bootlip spoiler that was build for the ce, will it fit?
Click to expand...
Yea
Click to expand...
Sure? I bought this one, and it was the wrong length for me CE, 85mm too long. Didn't read the year -.-
Measure the curved length of your boot edge and I'll measure mine. If it's about 85mm longer then get this one.
http://www.ebay.co.uk/itm/Painted-Mitsu ... AQ:GB:1123
Click to expand...

Cheers Jazza will take note, will take the measurements tomorrow it's freezing outside haha.
 
Does anyone know how to retrim the door cards. Mine's ugly as..... scratches and tears all over from the seat belts .... Wanted to take the whole grey vinyl off and put in new ones. Can someone post some DIYs or share their experience on retrimming vinyls?
 
Jazza said:
aviomen said:
Does anyone know how to retrim the door cards. Mine's ugly as..... scratches and tears all over from the seat belts .... Wanted to take the whole grey vinyl off and put in new ones. Can someone post some DIYs or share their experience on retrimming vinyls?
Click to expand...
DIY's have already been posted, in the DIY section.
viewtopic.php?f=41&t=4823
viewtopic.php?f=41&t=3530
Click to expand...

Thanks Jazza, but i have already checked those DIY post's out - actually my mistake i wasn't able to explain properly. I want to do the retrim for the entire door and not just the middle portion. The bottom bit that touches the doors have scratches and peeled vinyls - looks ugly as ..... so wanted to know how to change the entire door trim. Any help appreciated Thanks
 
^either go buy new door cards or follow those guides and just do the whole door instead. same principals as that one section but for the whole door. its not hard.
 
well i could get new door trims - but don't like the stock look anyways. Will try give that a shot - plenty of door trims around to practice on ;) However would have been good to see someone who already has done it ... would inspire more confidence ... haha :)
 
RegardedZero said:
What i need / how hard is it to change a 97 Mirage front bar to a MR bar :)
Click to expand...
All you need is the lip and cut out holes for the foggies if you have them to put on.
 
Not as straight forward, the mirage reo bar will not support an MR or Lancer bar properly, especially if you have the foglights sitting in the bar. It sags a lot and creates a 8mm or so gap between your headlights and bar. You need to get the appropriate reo bar if you would like for it to be properly supported.
 
Why are my cluster SMD LEDs burning out?

The two T10s and the T5 SMD LEDs on the left side of the cluster have burnt out, this has happened with multiple sets of SMD LEDs. The first one generally goes within about 30 minutes, the next follows a day or two later. The two T10s on the right are working fine and are no issues.
 
I haven't lost any of my LED's in the dash at all and every single one of my lights in the dash (and I mean absolutely everything) is LED. Might be the types of LED's you're getting?
 
It does seem to happen with the SMD LEDs in comparison to normal LEDs.. but they are working in one half of my cluster. I have tried a coupe different SMDs and the benefit of SMDs is so much greater.

T10-5SMD-WHITE.jpg
auto-smd-led-t10-05w-193.jpg
 
Do we have a thread for headlights?

Asking questions about replacement globes and whole units and what is legal on different models.

Also DRLs, fog and driving lights.
 
lancer1993 said:
Do we have a thread for headlights?

Asking questions about replacement globes and whole units and what is legal on different models.

Also DRLs, fog and driving lights.
Click to expand...

no 1 specific thread however it has been discussed in detail in many many many threads
 
You must log in or register to reply here.
Back
Top